5 Kia Picanto Key Fob Replacement Lessons Learned From Professionals

How to Replace a Kia Sportage Replacement Key

For many 2011 kia soul key fob programming models, the key contains a keyless entry system built-in. This key is similar to the remote control, and can be exchanged with a Kia dealer.

Key fobs might stop working due to a variety of reasons, including batteries that are dead, worn buttons signals, water damage, signal interference and a faulty receiver module. Here are some suggestions on how to get your Kia Sportage replacement key working again.

How to replace a smartkey or remote key?

The battery in your kia keys made's intelligent key will eventually need be replaced, regardless of whether it's a remote that starts with a push button or a standard metal key that does not contain transponder. This is especially when the vehicle displays a message that indicates that the smart or remote key is not powered by the battery.

Luckily, it's an easy process. In order to replace the key fob battery, remove the mechanical key from the hole in the back of the key fob. Then pry open the cover. Inside the key fob will be tiny screws that hold the battery in its place. By using a small screwdriver loosen the screw and remove the battery that was in place. Install the new battery and close the gap on the key fob.

Test the key fob by pressing the lock and unlock buttons. If the doors unlock and lock in the same way, you're all set! You can now use Kia's hands-free lock/unlock function when your fingers start to get cold or you have to go on errands around Brandon.

Note: Certain key fobs (transponder chip or smart keys) might require their programming done. This requires a programming machine, which is only available to the locksmith for cars or dealer. Other keys (non-transponder metal keys) don't require programming. If your key requires to be programmed again, you will need to be aware of the key code that is stamped on the tag of the key code and keep it in a safe place.

How do you replace a dead battery?

If the kia optima key replacement key fob doesn't respond to pressing the lock/unlock button, it's a sign that the battery is low. A low battery may cause other issues, like the check engine light coming on or the engine not working properly. It is easy to replace key fob batteries with only the use of a few tools.

Before starting the process, make sure that your vehicle is off and all doors are closed. Find the small, metal or plastic piece near the bottom of the key fob. Move it until the metal key falls out. You can then insert the key into the door handle of the driver to unlock your car.

To replace the battery inside the key fob, take off the cover that covers the rear. Utilize a plastic plier tool to open the latch that holds the black negative cable. Remove the old battery, and then align the new battery so that the "+" positive side faces you, while the "-" negative side is facing towards the fob's metallic electrical contacts. Push the new CR2032 battery straight into position without putting too much force on it to avoid bending or damaging the metal contacts.

After the new battery has been installed, turn the key fob off and then on in the ignition several times until the door locks cycle. You can then test the kia key case's Key fob again to confirm that it's working properly.

How do you replace the smart key

You could have a standard keyfob or a Smart Key based on the model of Kia Sportage. The smart key is equipped with an embedded mechanical key blade, while the standard keyfob does not. Both types of key fobs have batteries which eventually needs to be replaced. It's an easy task that will take about two minutes.

Make sure you turn off your Kia, and be on a flat, well-lit surface before you begin. Also, keep in mind that there are tiny parts inside the fob that can fall out if not vigilant.

The release button for the small size is located on the lower backside. It will be either a circular silver button or a rectangular slot. After pressing this button button, the mechanical blade will come out and you can then open the key fob.

Once the key fob is removed, you can remove the battery that was in it. The new battery should be a CR-2032, and can be purchased online or at a local auto parts store. When you are done with the battery, you should be able to lock, unlock and start your car using your key fob even if your engine isn't running!

How do you replace a broken mechanical key

The Kia key fob is a great option that lets us lock and unlock our car with the press of an button. Like any other device there are issues with it at times. There are steps to take to troubleshoot these issues and ensure that our key fobs are in good working order in the long run.

One of the most frequently encountered problems is a weak or dead battery. This can cause the fob to cease working or work intermittently. If this is the case you should replace the battery with a fresh new one.

If this isn't enough to resolve the issue Try using a standard flat-head screwdriver to break open the casing of the fob's plastic. Be careful not to damage any internal components or scratch the plastic. After the battery has been removed, replace it with a brand new one.

Close and open the door with the mechanical key. (Every kia fob comes with a spare mechanical key which will fit into the slot). Test the key fob and check that it's functioning properly. If the fob not working, contact an authorized locksmith or dealer to help solve the issue. Make sure they cut you an emergency key that can work in all the trunk and door cylinders in order to avoid future lockouts.